Mar 18, 2024 Leave a message

Ferrovanadium: Properties and Characteristics

Daniel
Daniel
Daniel is responsible for ferro alloy products at Zhen An International, including ferro silicon, ferro vanadium, ferro manganese and silicon manganese, with a focus on specs, COA, packing and export quotation support.

What Is Ferrovanadium?

Ferrovanadium, abbreviated FeV, is an iron-vanadium ferroalloy used mainly to introduce vanadium into steel. Commercial grades include FeV40, FeV50, FeV60, and FeV80, with the grade number indicating the approximate vanadium concentration range. Vanadium content is not the only purchasing parameter: carbon, silicon, aluminum, phosphorus, and sulfur may also enter the melt with the alloy and should remain within the downstream steel specification.

How Does Vanadium Strengthen Steel?

Vanadium strengthens many steels mainly through precipitation strengthening and grain-structure control. Vanadium interacts strongly with carbon and nitrogen. During suitable rolling, forging, cooling, or heat-treatment conditions, fine vanadium carbides, nitrides, or carbonitrides can precipitate from the steel matrix. These particles obstruct dislocation movement and contribute to increased yield strength, and they can also restrict grain growth and help produce a finer microstructure. The final effect depends on vanadium content, carbon and nitrogen levels, processing conditions, cooling rate, and heat treatment.

Ferrovanadium Grades and Differences

Grade V (%) C (max %) Si (max %) P (max %) S (max %) Al (max %)
FeV40-A 38-45 0.60 2.0 0.08 0.06 1.5
FeV40-B 38-45 0.80 3.0 0.15 0.10 2.0
FeV50-A 48-55 0.40 2.0 0.06 0.04 1.5
FeV50-B 48-55 0.60 2.5 0.10 0.05 2.0
FeV60-A 58-65 0.40 2.0 0.06 0.04 1.5
FeV60-B 58-65 0.60 2.5 0.10 0.05 2.0
FeV80-A 78-82 0.15 1.5 0.05 0.04 1.5
FeV80-B 78-82 0.20 1.5 0.08 0.05 2.0

The main difference between grades is the amount of vanadium supplied per unit mass of ferrovanadium. FeV40 has a lower V concentration and requires more alloy mass for the same vanadium addition; FeV50 is a medium concentration used where the specification is built around approximately 50 percent V; FeV60 provides more contained V per unit mass; and FeV80 provides high contained V while reducing the total alloy addition required for a given V target. A higher grade is not automatically better; buyers should compare vanadium recovery, impurity limits, required addition mass, and cost per unit of contained vanadium. Final acceptance should follow the agreed purchase specification and the actual batch certificate of analysis.

How Is Ferrovanadium Produced?

Ferrovanadium production generally starts with a vanadium-rich oxide feed that is reduced together with an iron source. One important upstream route starts with vanadium-titanium magnetite: vanadium is concentrated into vanadium-bearing slag, which is processed through roasting, leaching, and purification to produce vanadium oxides such as V2O5 or V2O3 that serve as feedstock for ferrovanadium smelting.

What Is Ferrovanadium Used For?

Ferrovanadium is used in high-strength and microalloyed steel, tool and die steel, spring and engineering steel, and selected cast irons and wear-resistant alloys where vanadium strengthening, grain control, or vanadium carbide formation is required.

Frequently Asked Questions

What are the main ferrovanadium grades? Commercial supply commonly includes FeV40, FeV50, FeV60, and FeV80.

How does vanadium strengthen steel? It forms fine VC, VN, and V(C,N) precipitates that contribute to precipitation strengthening and influence grain structure.

Is FeV80 always better than FeV50? No. FeV80 contains more vanadium per unit mass, but impurity limits, recovery, process requirements, and cost per unit of contained vanadium should also be compared.

What should be checked on a ferrovanadium COA? The parameters agreed in the purchase specification, normally including V, C, Si, Al, P, and S.

Which upstream route supplies ferrovanadium feedstock? Vanadium-titanium magnetite is processed through roasting, leaching, and purification to produce V2O5 or V2O3 for smelting.

Where is ferrovanadium applied? High-strength and microalloyed steel, tool and die steel, spring steel, and selected cast irons and wear-resistant alloys.

Send Inquiry

Home

Phone

E-mail

Inquiry