May 01, 2025 Leave a message

How Ferrosilicon Products Are Classified by Smelting Method

Why the Smelting Route Defines a Ferrosilicon Grade

Ferrosilicon is an iron-silicon master alloy that carries 15% to more than 90% silicon, and it is bought for two duties: deoxidation of liquid steel and the introduction of silicon into alloy and cast irons. Two furnaces can produce metal with the same silicon content yet deliver very different products, because the smelting route controls carbon, aluminium, titanium and calcium, and those residuals decide where the material can be used.

Classification by smelting method is therefore the first filter in a purchase enquiry. It separates high-silicon grades made for special alloy work, conventional grades from the standard submerged-arc furnace, low-aluminium grades for welding and electrical steel, and refined grades produced outside the furnace when impurity levels have to be pushed down further than normal smelting allows.

High-Silicon Ferrosilicon

High-silicon material is produced when the furnace charge and the reduction conditions are pushed towards the silicon end of the system, giving products with silicon content approaching the top of the practical range, generally above 90% Si and up to about 97% Si in specialised grades. This metal has a low iron content and a very low carbon content, which makes it useful as a feedstock for special alloy melting, for the production of silicone and silane chemistry, and for applications where carbon pick-up is unacceptable. It is brittle and is normally supplied in small, screened sizes.

General-Purpose Ferrosilicon

The general grade is the workhorse of the submerged-arc furnace and covers the FeSi 72 and FeSi 75 families, plus lower grades down to FeSi 45 for deoxidation duties where silicon units are required and a high silicon assay is not. FeSi 75 is the reference grade in most steelplant practice, and it is the material that appears in the standard specifications: GB/T 2272 sets out the silicon content and aluminium classes for the Chinese grades, ISO 5445 defines ferrosilicon for international trade, and ASTM A100 covers the grades commonly quoted in North American contracts.

Aluminium is the property that varies most between heats, because it follows the ore and the reduction practice. Buyers who need a predictable aluminium input specify an aluminium class rather than relying on typical values.

Low-Aluminium Ferrosilicon

Low-aluminium grades are made by selecting clean ore and controlling the furnace, and they are normally specified with aluminium at 1.0% maximum, with tighter classes down to 0.5% and, on request, below 0.1%. The driver is downstream behaviour: aluminium in the steel raises the risk of alumina inclusions and affects grain growth in electrical steels, and in welding consumables it alters the slag system and the toughness of the deposited metal. For these applications the aluminium limit is often more important than the silicon assay itself.

High-Purity Ferrosilicon from Refining Outside the Furnace

Refined ferrosilicon is produced by treating the liquid alloy after tapping, typically with oxygen or an oxidising slag, to burn out aluminium, calcium and carbon. The result is material with extremely low interstitial and tramp content, used for high-grade electrical steels, special welding wires and precision alloys where the residual budget is measured in a few hundredths of a percent. Because refining adds a processing step and reduces yield, refined grades carry a distinct price level and should only be specified where the residual limits genuinely require them.

Typical Chemistry by Class

Class Silicon Aluminium Carbon
High-silicon grades above 90% controlled by ore selection very low
General FeSi 75 74–80% 0.5–2.0% by class 0.1–0.2% typical
General FeSi 72 70–75% 1.0–2.0% 0.1–0.2% typical
Low-aluminium 70–80% 1.0% max, tighter on request 0.05–0.1%
High-purity refined 70–80% 0.05–0.5% 0.02–0.05%

Values vary with producer and with the ordered class; the certificate of analysis for the actual lot is the governing document, and aluminium, titanium and calcium should be reported per heat rather than as a monthly average.

Size, Packing and Appearance Checks

Ferrosilicon is supplied as lump, as graded cuts for cored wire, and as powder for dense-media and welding use. Size is a true specification item: a 1–3 mm cut and a 10–50 mm lump are different products commercially even at identical chemistry. On receipt, look for a clean grey fracture surface without heavy surface oxidation or moisture, and check that the screen cut contains neither a large coarse tail nor an excess of fines, since both distort dissolution behaviour in the ladle.

Frequently Asked Questions

Q: What does FeSi 75 mean?
A: It denotes a ferrosilicon grade with about 75% silicon. The exact range, together with aluminium classes and impurity ceilings, is fixed by the applicable specification such as GB/T 2272 or ISO 5445.

Q: Why is low-aluminium ferrosilicon more expensive?
A: Cleaner ore and tighter furnace control reduce the usable yield, and additional processing is sometimes required. The tighter aluminium limit costs money to guarantee heat after heat.

Q: When is refined high-purity ferrosilicon justified?
A: When the steel or welding consumable sets a residual budget for aluminium, calcium and carbon that ordinary smelting cannot meet, for example high-grade electrical steels and precision alloys.

Q: Which silicon content is used for deoxidation?
A: The FeSi 72 and FeSi 75 families cover most deoxidation duties. Higher-silicon grades are reserved for special alloy and chemical uses rather than bulk deoxidation.

Q: Does size affect performance?
A: Yes. Fine material dissolves faster and suits cored wire or ladle trimming, while lump is used for furnace charging. Screen cut and fines content should be written into the order.

Q: How should ferrosilicon be stored?
A: Dry, under cover, off the ground. Moisture promotes surface oxidation and can cause spitting during charging, and wet fines are difficult to feed reliably.

Send Inquiry

Home

Phone

E-mail

Inquiry