Mar 29, 2024 Leave a message

Ferrochrome Grades and How to Choose the Right Type

Mia
Mia
Mia is responsible for electrolytic manganese metal and refractory material content at Zhen An International, including EMM flakes, V2O5 and metallurgical additives, focusing on specs, COA, packing and export quotations.

Last Updated: August 13, 2026

Ferrochrome, also called ferrochromium or FeCr, is an iron-chromium alloy used mainly to introduce chromium into steel and other ferrous alloys. Commercial ferrochrome is available in high-carbon, medium-carbon, low-carbon and very-low-carbon specifications, with the appropriate grade depending mainly on the required chromium addition and the remaining carbon allowance in the steel.

In addition to Cr and C, buyers should also check Si, P and S limits, particle size and batch quality documentation. Common supply sizes include 10–50 mm, 50–100 mm and 10–100 mm, while other sizes can be agreed according to the charging system and furnace practice.

What Is Ferrochrome?

Ferrochrome is a ferroalloy containing chromium, iron and a controlled amount of carbon and other elements. Its main industrial function is to supply chromium during steelmaking and alloy production.

Chromium is important because it changes the oxidation resistance, corrosion behavior, hardness and high-temperature performance of steel. However, the ferrochrome grade cannot be selected from chromium content alone because the alloy also introduces carbon, silicon, phosphorus and sulfur into the melt.

This is why ferrochrome is commonly classified according to carbon level. High-carbon ferrochrome is suitable where more carbon can be tolerated, while low-carbon and very-low-carbon grades are used when chromium must be added without significantly increasing the steel's carbon content.

Main Types of Ferrochrome

The main difference between high-, medium-, low- and very-low-carbon ferrochrome is the amount of carbon delivered together with chromium.

Ferrochrome Type Carbon Position Selection Logic
Very-Low / Micro-Carbon FeCr Lowest carbon range Used when chromium addition is required with very limited additional carbon.
Low-Carbon FeCr Low carbon Selected for steel grades with tighter carbon control.
Medium-Carbon FeCr Intermediate carbon Used where some carbon input is acceptable but high-carbon FeCr would add too much.
High-Carbon FeCr Highest carbon range Common bulk chromium source where the steelmaking route can accommodate its carbon input.

The correct grade therefore depends on the target Cr content and the remaining carbon allowance in the melt rather than on the assumption that a lower-carbon grade is always better.

Typical Ferrochrome Chemical Composition

The following table retains the FeCr-1 to FeCr-8 specifications currently used on this page. These values should be treated as supply reference specifications rather than universal limits for every ferrochrome producer or standard.

Type Grade Cr (%) C (%) Si (%) P (%) S (%)
Micro Carbon FeCr-1 58–68 0.03–0.15 1.0–2.0 0.03–0.06 0.025–0.03
FeCr-2 63–68 0.03–0.15 1.0–2.0 0.03–0.06 0.025–0.03
Low Carbon FeCr-3 58–68 0.25–0.5 1.5–3.0 0.03–0.06 0.025–0.03
FeCr-4 63–68 0.25–0.5 1.5–3.0 0.03–0.06 0.025–0.03
Medium Carbon FeCr-5 58–68 1.0–4.0 1.5–3.0 0.03–0.06 0.025–0.03
FeCr-6 63–68 1.0–4.0 1.5–3.0 0.03–0.06 0.025–0.03
High Carbon FeCr-7 58–68 4.0–10.0 3.0–5.0 0.03–0.06 0.03–0.06
FeCr-8 63–68 4.0–10.0 3.0–5.0 0.03–0.06 0.03–0.06

Specification Note: Final chemical composition should follow the agreed purchase specification and shipment batch COA. Buyers should not select ferrochrome only by the labels "high carbon" or "low carbon" because Cr, Si, P and S limits can also affect suitability.

Ferrochrome Product Appearance

Ferrochrome alloy lumps in industrial supply

What Is Ferrochrome Used For?

Ferrochrome is used primarily as a chromium-bearing alloy addition in steelmaking. The carbon grade selected depends on the steel composition and the stage at which chromium is added.

High-Carbon Ferrochrome

High-carbon ferrochrome is widely used as a bulk chromium source where the steelmaking process can accommodate its carbon input.

It is particularly relevant to chromium-bearing and stainless steel production, where both chromium addition and overall alloying cost are important. The final suitability still depends on the steel plant's decarburization route and target carbon level.

For direct product specifications, see our high-carbon ferrochrome lumps for steelmaking.

Medium-Carbon Ferrochrome

Medium-carbon ferrochrome provides chromium with less carbon than high-carbon material. It can be selected where the steel has a more limited carbon allowance but does not require the very low carbon input of low-carbon FeCr.

The appropriate carbon level should be calculated from the existing melt chemistry and the required final specification rather than from the application name alone.

Low-Carbon and Micro-Carbon Ferrochrome

Low-carbon and very-low-carbon ferrochrome are selected when chromium must be added while minimizing additional carbon.

This can be important in low-carbon stainless steel, heat-resistant steel and other alloy systems where the carbon window is narrow. In these cases, buyers should pay particular attention to the actual C value on the batch COA.

How Is Ferrochrome Produced?

The ferrochrome production route depends strongly on the required carbon level.

High-Carbon Ferrochrome Production

High-carbon ferrochrome is commonly produced by reducing chromite-bearing raw material with a carbonaceous reductant at high temperature. The resulting alloy contains chromium and iron together with a relatively high carbon level.

After smelting, the alloy is tapped, solidified, crushed and classified into the required commercial particle-size range.

Lower-Carbon Ferrochrome Production

Lower-carbon ferrochrome requires additional control of carbon during production. Various refining and reduction routes can be used depending on the plant, starting material and required final carbon level.

The practical difference for the buyer is that stronger carbon control generally requires a different production route and should be verified through the actual FeCr specification and COA.

Why Does Ferrochrome Particle Size Matter?

Ferrochrome particle size affects charging, handling and dissolution behavior in the furnace or ladle.

Common commercial sizes include 10–50 mm, 50–100 mm and 10–100 mm. The correct range depends on the charging method, furnace size and alloy-addition practice.

Very large lumps may require longer dissolution time under some conditions, while excessive fines can increase handling loss, oxidation exposure and dust generation.

For this reason, particle size should be written into the purchase specification instead of being treated as a secondary packaging detail.

High-Carbon vs Low-Carbon Ferrochrome: How to Choose

The main selection question is how much carbon can still be introduced while reaching the required chromium level.

Selection Factor High-Carbon FeCr Low / Micro-Carbon FeCr
Carbon Input Higher Lower
Main Selection Logic Suitable where the process can tolerate or later remove more carbon Suitable where additional carbon must be limited
Chromium Addition Bulk chromium alloying Controlled chromium correction under tighter carbon limits
Buyer Focus Cr, C, Si, P, S and alloy cost Cr, especially C, plus Si, P and S

A higher-priced low-carbon grade is not automatically necessary if the steelmaking route can accommodate the carbon contained in high-carbon FeCr. Conversely, using high-carbon ferrochrome can create unnecessary chemistry-control problems when the remaining carbon allowance is very small.

What Should Buyers Check Before Ordering Ferrochrome?

A ferrochrome purchase specification should define chemistry, particle size and quality documentation.

Purchase Item What to Confirm
Ferrochrome Type High-, medium-, low- or micro-carbon grade
Cr Content Required chromium range
C Content Maximum carbon compatible with the target steel chemistry
Si / P / S Maximum limits required by the downstream process
Particle Size 10–50 mm, 50–100 mm, 10–100 mm or another agreed range
Batch COA Actual chemical analysis corresponding to the shipment batch
Packing Bag size and shipment requirements

FAQ About Ferrochrome Grades

Q:What is ferrochrome mainly used for?

A:Ferrochrome is mainly used to introduce chromium into steel and other iron-based alloys. The required grade depends on the target chromium content and carbon allowance.

Q:What is the difference between high-carbon and low-carbon ferrochrome?

A:The main difference is carbon content. High-carbon ferrochrome introduces more carbon together with chromium, while low-carbon ferrochrome is used where chromium needs to be added with tighter control of the final carbon level.

Q:What chromium content does ferrochrome contain?

A:The current reference specifications on this page cover approximately 58–68% Cr depending on grade. The exact contractual range should be confirmed before ordering.

Q:Which ferrochrome grade is used for stainless steel?

A:Different ferrochrome grades can be used in stainless steel production. The correct choice depends on the production route, target Cr and C levels, and whether the process can remove carbon after alloy addition.

Q:What ferrochrome particle size is commonly supplied?

A:Common commercial sizes include 10–50 mm, 50–100 mm and 10–100 mm. Custom sizes can also be agreed according to the furnace and charging system.

Q:What should a ferrochrome COA include?

A:A batch COA should identify the shipment batch and report the agreed chemical values, normally including Cr, C, Si, P and S according to the purchase specification.

Need Ferrochrome for Steelmaking?

Send us your required Cr content, carbon limit, Si/P/S limits, particle size, quantity and destination port. We can confirm available ferrochrome specifications, packing and batch COA before quotation.

Request Ferrochrome Quote

 

 

Send Inquiry

Home

Phone

E-mail

Inquiry