High carbon ferromanganese is the most heavily used manganese master alloy in steelmaking. It is produced by smelting manganese ore with carbon in a furnace, and it supplies manganese in a robust and economical form. Because almost all steel contains manganese, the material is traded in very large quantities and its quality has a direct effect on steel cost and properties.
Composition and Typical Grades
High carbon ferromanganese typically contains manganese in the range of about seventy six to eighty two percent, with carbon around six to eight percent and a balance of iron, together with controlled levels of silicon, phosphorus and sulphur. The exact ranges are set by the specification used. GB/T 3795 is a widely referenced standard for ferromanganese, and it defines grades by manganese content and by the limits on carbon, silicon, phosphorus and sulphur. Grades are also distinguished by size, from large lumps suitable for the furnace to smaller sizes for ladle additions, and by whether they are supplied as standard or low phosphorus material. Low phosphorus grades are reserved for steels where phosphorus must be tightly controlled.
Supplying Manganese for Alloying
The primary function of high carbon ferromanganese is to provide manganese as an alloying element. Manganese improves the hardenability, strength and toughness of steel, and it is present in essentially every commercial steel grade. It also combines with sulphur to form manganese sulphide, which prevents the formation of harmful iron sulphide that would cause hot shortness during rolling. Because the manganese requirement is large compared with most other alloying elements, the addition is made with a high manganese master alloy rather than with pure metal, and high carbon ferromanganese is the standard choice for this purpose.
Deoxidation and Desulphurisation
Manganese acts as a mild deoxidiser and works together with silicon to control the oxygen content of the steel. In the ladle it also contributes to desulphurisation, particularly when the slag is designed to favour the removal of sulphur. Manganese sulphide inclusions that form are relatively plastic and less damaging than some alternative inclusions, and their shape can be further controlled with calcium treatment. These combined effects are why manganese additions are made at several stages of the steelmaking process rather than in a single step.
Use in Foundries and Other Alloys
Beyond steelmaking, high carbon ferromanganese is used in foundries to adjust manganese in cast iron, where it influences structure and hardenability. It also serves as a feedstock for making other manganese products and as an economical source of manganese in some non ferrous and welding applications. In each case the carbon content limits where the material can be used, because high carbon is undesirable in low carbon products. Where a lower carbon content is needed, medium or low carbon ferromanganese is substituted at a higher cost.
Selection, Handling and Quality
Buyers should check manganese content, carbon, silicon, phosphorus and sulphur, together with sizing and moisture. Phosphorus is often the critical element, because it is difficult to remove in the steelmaking process and its level in the alloy directly affects the final steel. Consistent sizing improves dissolution and recovery, and sealed packaging protects the material during transport. As with all ferroalloys, the delivered lot should be accompanied by a certificate of analysis so that the charge can be calculated accurately and the steel specification met with confidence.
Frequently Asked Questions
Q: What is high carbon ferromanganese?
It is an iron manganese master alloy with a high carbon content, typically about six to eight percent carbon, used mainly to add manganese to steel.
Q: What does ferromanganese do in steel?
It supplies manganese for alloying, assists deoxidation and helps prevent hot shortness by binding sulphur as manganese sulphide.
Q: How much manganese is in high carbon ferromanganese?
Most commercial grades contain between about seventy six and eighty two percent manganese, with iron and controlled carbon making up the balance.
Q: Why is low phosphorus ferromanganese more expensive?
Phosphorus is difficult to remove in steelmaking, so producing a low phosphorus alloy requires better ore selection and closer process control, which raises cost.
Q: Which standard covers ferromanganese?
GB/T 3795 is a widely referenced standard, and it defines grades by manganese content and by limits on carbon, silicon, phosphorus and sulphur.


