Dec 04, 2023 Leave a message

What Is the Main Role of Ferromanganese in Steelmaking and Foundry Practice

What Ferromanganese Is and How the Grades Are Divided

Ferromanganese is a manganese-iron alloy, and after ferrosilicon it is the largest tonnage ferroalloy consumed by the steel industry. It is produced by carbothermic reduction of manganese ore, either in a blast furnace or in an electric submerged-arc furnace. The production route and the refining step that follows determine how much carbon remains in the alloy, and carbon content is the basis of the commercial classification used across the trade.

The carbon classes in common use are: micro carbon, with carbon not more than 0.15 percent; low carbon, above 0.15 percent and up to 0.7 percent; medium carbon, above 0.7 percent and up to 2.0 percent; and high carbon, above 2.0 percent and up to 8.0 percent. The two families are also named by melting route: electric-furnace ferromanganese and blast-furnace ferromanganese. Designated grades follow GB/T 3795 in China, with ISO 5446 and ASTM A99 covering the same product in international and North American purchasing.

Deoxidation and Desulfurisation in Steelmaking

Manganese is a workhorse deoxidiser and desulfuriser. In the bath it removes dissolved oxygen, and the resulting manganese oxide partitions into the slag. Its more important role, however, is sulfur control: manganese combines with sulfur to form manganese sulfide, MnS, which is far less damaging than iron sulfide. Iron sulfide forms low-melting films along grain boundaries and causes hot shortness during rolling or forging. Manganese sulfide, by contrast, forms as discrete inclusions with a high melting point, so the steel can be hot worked without cracking.

Because the reaction is driven by the manganese to sulfur ratio, plants target a minimum Mn:S ratio rather than a fixed manganese addition. A ratio of at least 20 to 1 in the liquid steel is a common requirement for plain carbon and low-alloy grades, with higher ratios used where sulfur is deliberately kept very low and sulfide shape control is applied. Excess manganese beyond that needed for sulfur control remains in solid solution and contributes to hardness and strength.

Ferromanganese is comparatively inexpensive per unit of manganese, which is why it is preferred over more costly deoxidisers for bulk oxygen and sulfur removal. It is added during tapping or in the ladle, and its cost per tonne of steel treated is one of the lowest of any ferroalloy used at tonnage scale.

Manganese as an Alloying Element

Almost every commercial steel contains manganese as an intentional alloying element rather than only as a scavenger. Manganese raises hardenability by retarding the transformation of austenite, which allows thicker sections to be through-hardened and allows slower, less distortion-prone quenching. It also raises strength through solid solution, improves toughness when balanced against carbon, and is a stabiliser of austenite in the higher-manganese families.

Typical manganese contents reflect the different jobs it performs. Structural and pressure-vessel steels generally sit between 0.60 and 1.60 percent. Free-machining grades can reach 1.5 percent with sulfur and lead additions to form machinable inclusions. Austenitic manganese steels used in wear-resistant castings carry far higher levels, and the classic Hadfield composition relies on roughly 11 to 14 percent manganese with about 1.0 to 1.4 percent carbon to produce a work-hardening austenitic structure. The ferromanganese grade selected for making such a steel must be low in carbon if the carbon balance is tight.

Carbon Classes and Typical Grades

Carbon class Carbon content Melting route Typical duty
Micro carbon Not more than 0.15 % Refined, oxygen-blown Welding consumables, low-carbon steels
Low carbon Above 0.15 % up to 0.7 % Refined, oxygen-blown Alloy steels with tight carbon limits
Medium carbon Above 0.7 % up to 2.0 % Electric furnace with refining Alloy and tool steels
High carbon Above 2.0 % up to 8.0 % Blast furnace or electric furnace Bulk deoxidation and desulfurisation
Grade Mn C, max Si, max
FeMn78C8.0 75.0 to 82.0 % 8.0 % 2.0 %
FeMn78C2.0 75.0 to 82.0 % 2.0 % 1.5 %

The first two digits of the designations above refer to the nominal manganese content, the letter C stands for carbon and the trailing number is the maximum carbon permitted. The table is deliberately short: several micro carbon and low carbon grades sit either side of these limits, and the correct grade is always the one written on the applicable standard for the specific heat.

Use in the Foundry Industry

Foundries consume ferromanganese for cast iron and for steel castings. In grey and ductile iron it adjusts manganese to control the balance between pearlite and ferrite, and it counteracts the harmful effect of sulfur carried in from coke and scrap. Manganese also ties up sulfur in the charge so that spheroidising treatment in ductile iron is not poisoned by sulfur, though this has to be balanced against carbide formation, because excess manganese promotes carbides and can lower ductility.

In steel foundries the alloy is used for deoxidation and manganese alloying in the same way as in steelmaking, typically charged into the furnace or added to the ladle or the pouring stream. Because foundry heats are smaller and more variable in chemistry, screen sizing matters more than in an integrated mill; a mid-size lump that dissolves reliably in a short superheat window is generally preferred over coarse material.

Handling, Storage and Addition Practice

Ferromanganese is shipped in drums, big bags or in bulk. High carbon grades are dense and relatively stable in storage, while finely crushed refined grades can pick up moisture and should be kept covered and dry. Screened fractions for ladle addition are usually supplied in the 10 to 50 mm range, with finer material used for cored wire and for briquetted additions.

For process control, the additions that matter are manganese for the sulfur balance, carbon for the specified maximum, and phosphorus for grades with residual element limits. Recovery of manganese in the ladle normally sits in the 85 to 95 percent range depending on slag basicity, temperature and the amount of oxygen still present when the alloy is added. Sampling the alloy on arrival, checking the sieve analysis against the order and keeping lot traceability are the practical controls that keep the manganese balance predictable from heat to heat.

Frequently Asked Questions

Q: What is the main role of ferromanganese in steelmaking?
A: It provides manganese for combined deoxidation and desulfurisation, and for alloying. Manganese forms MnS instead of harmful iron sulfide and raises hardenability and strength.

Q: How is ferromanganese classified?
A: By carbon content: micro carbon not more than 0.15 percent, low carbon from above 0.15 to 0.7 percent, medium carbon from above 0.7 to 2.0 percent, and high carbon from above 2.0 to 8.0 percent.

Q: Which standard covers high carbon ferromanganese?
A: GB/T 3795 in China and ISO 5446 internationally, with ASTM A99 used in North America. The grade designation states manganese content and maximum carbon, for example FeMn78C8.0.

Q: Why is a minimum manganese to sulfur ratio specified?
A: Sulfur is only tied up when enough manganese is present. A ratio of at least 20 to 1 in the liquid steel is common practice, because below that threshold residual iron sulfide can cause hot cracking during hot working.

Q: Can medium carbon ferromanganese be used in a low-carbon steel?
A: Only if the carbon budget allows. A grade carrying up to 2.0 percent carbon adds carbon to the heat, so low carbon and micro carbon grades are selected when the specified maximum carbon is tight.

Q: What is the typical manganese recovery in the ladle?
A: Generally 85 to 95 percent, depending on slag basicity, tapping temperature and how much dissolved oxygen remains when the alloy is added.

Send Inquiry

Home

Phone

E-mail

Inquiry